Fretwork along with Scroll Sawing Suffers from.

Fretwork is “decoration or patterns or patterns on a surface made by cutting into or through the surface”, in accordance with Merriam-Webster’s Dictionary. But if you ask me, fretwork and scroll sawing, because it is frequently known, is a superb way to relieve stress and at the same time frame get a feeling of accomplishment when your item is finished. There’s a wide selection of materials that can be used for fretwork, including thick paper, numerous wood materials, soft metals and plastics. Although I have used Plexiglas, plywood and cardboard, my true passion for scroll sawing is wood.

From my viewpoint, the hardest part of using wood is having the board to a finished thickness and smoothness so your pattern may be attached. There are numerous locations that you can buy finished lumber, beginning with as thin as 1/8″ Baltic birch and up. When you yourself have the necessary tools, probably the most economical way to begin with is to purchase rough cut lumber from a local lumber yard. Rough cut lumber is generally 1″ to 1 1/4″ thick, and most lumberyards may have one edge trim so you can start out with a straight edge. There are so many beautiful grained hardwoods available, though I primarily use oak, cherry and walnut. Now, the wood is run via a band-saw and cut into strips, anywhere from 2″ to 2 1/2″ wide, depending on the original width of the board, so they are fairly uniform in width.

Once cut into strips, the strip is switched on its side and explain to you the band-saw again, cutting it so it’s between ½ and ¾ inches thick. I like to make use of what they call a re-saw blade in my own band-saw, one that is anywhere from ¼” to ¾” wide. I usually be sure that I have the guard down as near to the little bit of wood that I will, never wear loose fitting clothes and wear protective eye goggles for safety reasons.

Once most of the strips are cut, they may be glued together, making certain the grain of the wood is alternated to prevent the wood from warping. Then all that’s left is putting on the finishing touches. I run both edges through the joiner to make sure I have an appartment, straight edge and then through the planer to obtain it down to the desired thickness.

Now I’m almost willing to use the scroll saw. When the pattern is selected, spray art glue is employed to lightly spray the rear of the pattern and put it on the finished board. When adhered to the wood, holes are drilled for every place where scroll saw blade access is needed. The clock shown only needed 21 holes drilled, but I did some designs where over 300 holes were needed. Depending on the scroll saw that you employ, it is fairly quick to detach the the surface of the blade and insert it from the bottom of your workpiece in order to commence to cut. Delta features a handy quick release blade chuck that’ll also focus on some other brands of saws.

One of the nice link between using a scroll saw, is that there is almost no sanding that really needs to be performed, mainly on the rear and sometimes in the corners, depending on how you do them. The blade that you employ will also determine how much sanding is needed on your own inner cuts. My preference could be the Olson Double-Tooth, Skipped Tooth blade; this indicates to keep a little cooler which means it lasts a little longer. One thing that you don’t want to make use of is a dull blade, because it is really hard to keep on your own lines with a dull blade, and sometimes you do not have a lot of room for veering off lines. When the piece is sanded to your satisfaction and glued together, all that is left if putting on the finish. I choose the natural grain and color of the wood, so I usually make use of a semi-clear gloss coating, which really enhances the natural grain.

It is really great to start with a bit of rough cut lumber and end up getting a keepsake. I demonstrated the scroll saw for A-Line Machine and Tool at some workshops they had on woodworking, and discovered this hobby is enjoyed by all ages. Kids as young as 9 years of age and around 90 years of age came in and wanted some tips about scroll sawing. There are always a lot of personal preferences when it comes to scroll sawing, including the device and blades used, cuts of wood or types of materials, or what finish is applied to their art. But most individuals who try it once, love utilizing the scroll saw.

Leave a Reply